First edition. International Standard IS0 10066 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 6 p. This international Standard describes the procedure for determining the creep of a flexible cellular polymeric material when compressed by a static force, intended primarily for quality assurance in packaging applications.
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 10282:2002), of which it constitutes a minor revision. — 16 p. This International Standard specifies requirements for packaged sterile rubber gloves intended for use...
First edition. International Standard ISO 10398 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 14 p. This International Standard specifies methods using gas chromatography (GC) and thin layer chromatography (TLC) for the separation and identification of the following classes of accelerators in vulcanized and unvulcanized compounds: - thiazoles; -...
First edition. ISO 10638 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 50 p. This International Standard specifies a qualitative method, using gas chromatography/mass spectrometry, for the identification of antidegradants in raw rubbers, latices, unvulcanized-rubber compounds and vulcanizedrubber products....
Second edition. ISO 11089 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 11089:1997), which has been technically revised. — 12 p. This International Standard describes a procedure for the determination of the following antidegradants in raw...
Second edition. ISO 11193-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 11193-1:2002), of which it constitutes a minor revision. — 14 p. This part of ISO 11193 specifies requirements for packaged sterile, or bulked non-sterile, rubber...
Amendment 1 to ISO 11193-1:2008 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 6 p.
First edition. ISO 11193-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This part of ISO 11193, together with ISO 11193-2, cancels and replaces ISO 11193:1994, which has been technically revised. — 16 p. This part of ISO 11193 specifies requirements for packaged sterile, or bulked non-sterile,...
First edition. International Standard IS0 11234 was prepared by Technical Committee lSO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw rnaterials (including latex) for use in the rubber industry. — 7 p. This International Standard specifies a method for determining the dust content of pelletized carbon blacks for use in the industry. This method permits a...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 11235:1999) , which have been technically revised. — 32 p. This International Standard specifies the methods to be used for the...
First edition. International Standard ISO 11236 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 26 p. This International Standard applies to a variety of substituted p-phenylenediamine (PPD) antidegradants used in the rubber industry. The three general classes of PPD...
Technical Corrigendum 1 to ISO 11236:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 2 p.
Third edition. International Standard ISO 1124 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This third edition cancels and replaces the second edition (ISO 1124:1983), of which it constitutes a technical revision. — 5 p. This International Standard specifies procedures for the sampling of carbon black for use in the rubber industry, delivered in...
Third edition. International Standard ISO 1125 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 1125:1990), which has have been technically revised. — 8 p. This International Standard specifies a method for...
Amendment 1 (15.05.2011) for the third edition of ISO 1125 (15.03.1999). Amendment 1 to ISO 1125:1999 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 6 p.
Fourth edition. ISO 1126 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third (ISO 1126:1992). Two additional methods have been included: a moisture balance method and an infrared irradiation method. — 12 p. This...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 11344:2004), which has been technically revised. — 26 p. This International Standard describes a method for the determination of the molecular mass, expressed as...
Second edition. ISO 11345 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 11345:1997), which has been technically revised. — 34 p. This International Standard specifies qualitative visual methods for the rapid and comparative assessment of the...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 11346:2004), of which it constitutes a minor revision. — 18 p. This International Standard specifies the principles and procedures for estimating the thermal endurance of...
Second edition. ISO 1138 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 1138:1981). — 10 p. This International Standard specifies three methods for the determination of the total sulfur in all types of...
Amendment 1 (15.04.2012) for the second edition of ISO 1138 (15.02.2007). Amendment 1 to ISO 1138:2007 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 6 p.
First edition. International Standard ISO 11752 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p. This International Standard specifies a method of deternining the hardness or compressibility of a material by measuring the compression and/or deformation force on flexible cellular polymeric profiles...
Amendment 1 to ISO 11752:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 6 p.
Second editiion. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 11852:2011) , which has been technically revised. — 14 p. This document specifies a titration method for the determination of...
First edition. ISO 12243 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 24 p. This International Standard specifies a method for the determination of the amount of water-extractable protein in natural rubber (NR) gloves for medical use. The method is potentially...
Amendment 1 to ISO 12243:2003 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 10 p.
Third edition. International Standard ISO 123 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 123:1985), which has been technically revised. The principal differences lie in more precise definitions and...
Seventh edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This seventh edition cancels and replaces the sixth edition (ISO 124:2011) which has been technically revised. — 14 p. This International Standard specifies methods for the determination of the...
First edition. ISO 12492 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 14 p. This International Standard specifies a test method for the determination of water content of raw rubber and compounded rubber using a coulometric Karl Fischer titration method. It applies to the water content range between 0,01 %...
First edition. ISO 12493 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 18 p. This International Standard specifies a method for measuring the stress in tension which is developed in vulcanized rubber when it is heated (thermal stress). The thermal stress is measured for various pre-strain and temperature...
Sixth edition. ISO 125 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This sixth edition cancels and replaces the fifth edition (ISO 125:2003), which has been technically revised. — 10 p. This International Standard specifies a method for the determination of the...
Fifth edition. ISO 126 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 126:1995), which has been technically revised and a statement of the precision of the method added. — 10 p. This International Standard...
Fourth edition. ISO 127 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 127:1995). — 16 p. This International Standard specifies a method for the determination of the KOH number of natural rubber latex...
First edition. International Standard ISO 12965 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 12 p. This International Standard specifies a method for the determination of the mictostructure of butadiene rubber (BR) by infra-red spectrometry using a cast film.
Technical Corrigendum 1 to ISO 12965:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 1 p.
Fifth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 1304:2006) , which has been technically revised. — 20 p. This International Standard specifies methods for the determination of...
Fourth edition. International Standard IS0 1306 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (IS0 1306:1987), which has been technically revised. — 5 p. This International Standard specifies a method for...
Fifth edition. ISO 132 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 132:2005), of which it constitutes a minor revision the main purpose of which was to add Annex A concerning calibration and Annex B with precision results. — 22 p. This...
Second edition. ISO 13226 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 13226:1999), in which the normative references have been updated. — 34 p. This International Standard specifies requirements for vulcanized rubbers in sheet form for use as...
Technical Corrigendum 1 to ISO 13226:2005 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 1 p.
First edition. International Standard ISO 13362 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p. This International Standard specifies a method for determining the compression set of flexible cellular materials under humid conditions. This method consists of maintaining the test piece under...
First edition. International Standard ISO 13773 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 10 p. This International Standard specifies a method for the determination of the alkalinity of polychloroprene latex prepared by the polymerization of chloroprene in an...
Fourth edition. ISO 1407 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 1407:2009), which has been technically revised with the addition of a Method D for raw rubbers only. — 22 p. This International Standard specifies four methods for the...
Third edition. International Standard IS0 1408 was prepared by Technical Committee lSO/TC 45, Rubber and rubber products. This third edition cancels and replaces the second edition (IS0 1408:1987), of which it constitutes a minor revision. — 11 p. This International Standard specifies a pyrolytic method (A) and two chemical degradation methods (B and C) for the determination of...
Fifth edition. ISO 1409 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 1409:1995), of which it constitutes a minor revision, primarily concerning updating of references and the deletion of references to the withdrawn standards ISO 842, ISO 1625...
Second edition. International Standard ISO 1419 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 1419:1977), which has been technically revised. — 8 p. This International Standard describes four methods of assessing the resistance of coated fabrics to deterioration by accelerated ageing.
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This fourth edition cancels and replaces the third edition (ISO 1420:2001) , which has been technically revised. — 14 p. This International Standard specifies two methods for the determination of the resistance of rubberor...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 1421:1998) , which has been technically revised. — 18 p. This International Standard specifies two methods for the determination of the tensile strength of fabrics...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 24 p. This International Standard specifies limits for extractable chemical substances for single-use gloves made from natural rubber, synthetic rubber, or plastic materials that are intended for use in food preparation, food...
First edition. ISO 14309 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 22 p. This International Standard specifies a method for the determination of the volume and the surface resistivity of vulcanized or thermoplastic rubbers. The method can be applied to materials with a resistivity from 10 1 Ω⋅m to 10 17...
First edition. International Standard ISO 1431-3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Physical and degradation tests. — 28 p. This part of ISO 1431 describes three types of method for the determination of ozone concentration in laboratory test chambers. Method A — UV absorption: this is the reference method, and is used...
Fourth edition. ISO 1432 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 1432:1988), which has been technically revised. — 18 p. This International Standard specifies a static procedure, known as the Gehman test, for determining the relative...
Fourth edition. International Standard ISO 1435 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 1435:1988), which has been technically revised. — 6 p. This International Standard specifies a method for the...
Fifth edition. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 1437:2007) , which has been technically revised. — 12 p. This document specifies a method for determining the water-wash sieve...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 14558:2000) , of which it constitutes a minor revision. — 12 p. This International Standard specifies a method for determining the...
First edition. ISO 14932 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 38 p. This International Standard specifies four methods for the determination of the content of the following groups of organic peroxides used as rubber vulcanizing agents. There are three...
Second edition. ISO 15113 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 15113:1999), of which it constitutes a minor revision. — 28 p. This International Standard outlines the principles governing the measurement of coefficient of friction and...
First edition. International Standard ISO 15671 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 10 p. This International Standard specifies an instrumental (automatic analyser) method for the determination of total sulfur in rubber and rubber additives.
First edition. International Standard ISO 15672 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 10 p. This International Standard specifies an instrumental (automatic analyser) method for the determination of total nitrogen in rubber and rubber additives.
Third edition. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 15825:2015) , which has been technically revised. — 16 p. This document specifies a method for determining the size distribution...
First edition. ISO 16010 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 16 p. This International Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from –5 °C up to 50 °C and in special...
Fourth edition. ISO 1652 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 1652:2004), which has been technically revised. The main change is the inclusion of precision data (see Annex B). — 14 p. This...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 1656:1996), which has been technically revised. — 24 p. This International Standard specifies a macro-method and a semi-micro method for the determination of nitrogen in raw...
First edition. ISO 16564 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 12 p. This International Standard specifies a method of determining the average molecular mass and the molecularmass distribution of raw natural rubber dissolved in tetrahydrofuran. A set of polystyrene standards is used for calibration...
Amendment 1 to ISO 16564:2004 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 8 p.
Third edition. SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 16565:2008), of which it constitutes a minor revision. — 20 p. This International Standard specifies the methods to be used to determine the content of 5-ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers in the 0,1 % to...
Third edition. ISO 1658 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 1658:1994), which has been technically revised. — 22 p. This International Standard specifies ⎯ physical and chemical tests on raw...
First edition. ISO 17052 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 20 p. This International Standard specifies a method for the determination of residual monomers and other volatile low-molecular-mass compounds in raw rubber by capillary column gas chromatography using a thermal desorption (also known...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 20 p. This International Standard provides a qualitative method for the identification of rubbers by their pyrolysis products using tandem the gas-chromatography /mass spectrometry. The method applies to rubbers in the raw state and to...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This International Standard specifies a method for the determination of gel content for technically specified rubbers (TSR).
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw material (including latex) for use in the rubber industry. — 16 p. This International Standard specifies a cyanide-free titration method for the determination of the magnesium content in field and concentrated natural rubber latex.
Second edition. ISO 17564 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 17564:2001), which has been technically revised. — 12 p. This International Standard specifies a method using Wijs' solution to determine the iodine value (i.e. the residual...
Fourth editon. ISO 1795 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 1795:2000), which has been technically revised. — 12 p. This International Standard specifies a method for the sampling of raw rubber...
Fourth edition. ISO 1798 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This fourth edition cancels and replaces the third edition (ISO 1798:1997), which has been technically revised. It also incorporates the Technical Corrigendum ISO 1798:1997/Cor.1:2003. The main change is the introduction of a second...
Sixth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This sixth edition cancels and replaces the fifth edition (ISO 1817:2011), which has been revised. — 30 p. This International Standard describes methods of evaluating the resistance of vulcanized and thermoplastic rubbers to the action of...
Fifth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 1827:2011) , which has been technically revised by changing symbols in 12.2.2. — 14 p. This document specifies methods for the determination of the modulus in shear and the...
Third edition. ISO 1853 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 1853:1998), which has been technically revised, mainly to add another two methods (methods 2 and 3). — 18 p. This International Standard specifies the requirements for the...
Third edition. International Standard ISO 1856 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 1856:1980), which has been technically revised. — 10 p. This International Standard specifies three methods for determining the compression set of...
Amendment 1 (15.09.2007) for the third edition of ISO 1856:2000. Amendment 1 to ISO 1856:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p.
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 10 p. This International Standard provides a general introduction to, and guidance on, the methods of test for low temperature properties of vulcanized and thermoplastic rubbers. It is intended to provide an understanding of the...
Fifth edition. ISO 188 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 188:2007), of which it constitutes a minor revision to include an annex (Annex D) specifying a calibration schedule for the apparatus used. — 28 p. This International Standard...
Second edition. ISO 18852 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 18852:2005), which has been technically revised. — 16 p. This International Standard specifies a method for the determination of the...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 18899:2004), of which it constitutes a minor revision. — 24 p. This International Standard outlines the principles of calibration of rubber test equipment and gives guidance...
First edition. ISO 19003 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 142 p. This International Standard provides guidance on the application of statistics to rubber testing. It is intended not to conflict with or replace existing International Standards covering basic statistical techniques, but rather to...
First edition. ISO 19004 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. This International Standard is based on ASTM D 6600-00, Standard Practice for Evaluating Test Sensitivity for Rubber Test Methods, copyright ASTM, used with permission of ASTM. — 38 p. This International Standard describes how test...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 22 p. This International Standard specifies a general method for determining the liquid absorption capacity of a pigment and extender by using di-(2-ethylhexyl) adipate (DOA, CAS 103-23-1) . The...
Seventh edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This seventh edition cancels and replaces the sixth edition (ISO 2000:2003) , which has been technically revised. — 12 p. This International Standard provides guidance on the specification of...
Fifth edition. ISO 2004 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 2004:1997), which has been technically revised. — 8 p. This International Standard gives specifications for natural rubber latex...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 2005:1992), which has been technically revised. It also incorporates the amendment ISO 2005:1992/Amd1:2006. — 10 p. This...
First edition. ISO 2006-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. It cancels and replaces ISO 2006:1985, which has been technically revised. — 14 p. This International Standard specifies a method for the determination of the high-speed mechanical stability of...
First edition. ISO 2006-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 22 p. This part of ISO 2006 specifies a method for the determination of the mechanical stability of synthetic rubber latex. This method measures the mass of coagulum formed when a test portion...
Fourth edition. ISO 2007 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommitte SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 2007:1991), which has been revised. — 8 p. This International Standard specifies a method for the rapid determination of the plasticity of raw rubber and unvulcanized...
Second edition. International Standard ISO 2023 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 2023:1973), which has been technically revised. — 19 p. This International Standard specifies requirements for lined industrial vulcanized-rubber ankle, half-knee, short-knee and knee-height...
Fourth edition. International Standard ISO 2028 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 2028:1989), which has been technically revised. — 9 p. This International Standard specifies four methods for...
First edition. ISO 20299-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 8 p. This part of ISO 20299 specifies the material and physical property requirements for non-strippable film for wrapping general-purpose synthetic rubber bales, intended to keep the bales...
Technical Corrigendum 1 to ISO 20299-1:2006 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 2 p.
First edition. ISO 20299-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 8 p. This part of ISO 20299 specifies the material and physical property requirements for non-strippable high melting point film for wrapping natural-rubber bales, intended to keep the bales...
First edition. ISO 20299-3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 8 p. This part of ISO 20299 specifies the material and physical property requirements for non-strippable film for wrapping general-purpose synthetic rubber bales and intended to keep the bales...
First edition. ISO 21171 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This International Standard is based on ASTM D 6124-01, Standard Test Method for Residual Powder on Medical Gloves, copyright ASTM, used with permission of ASTM. — 16 p. This International Standard...
Second edition. ISO 21461 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 21461:2006), to which a new annex (Annex C) has been added describing a procedure for the preparation of clean samples from the...
Amendment 1 to ISO 21561:2005 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 6 p.
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This first edition of ISO 21561-2 cancels and replaces ISO 21561:2005, which has been technically revised. It also incorporates Amendment ISO 21561:2005/Amd.1:2010. — 22 p. This part of ISO 21561 specifies procedures for the quantitative...
First edition. ISO 21869 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 22 p. This International Standard specifies the test methods to be used for magnesium oxide intended for use in the rubber industry as a stabilizer and vulcanizing agent. The choice of the...
First edition. ISO 21870 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 10 p. This International Standard describes a method for quantitative determination of the loss on heating (pyrolysis) of carbon black due to the elimination of volatile materials other than...
Second edition. International Standard ISO 2230 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 2230:1973), which has been technically revised. — 18 p. This International Standard gives guidelines for the inspection, recording procedures,...
Second edition. International Standard ISO 2231 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 2231:1973). — 6 p. This International Standard specifies the requirements for conditioning and methods of conditioning employed for rubber- or plastics-coated fabrics.
Second edition. ISO 22762-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 22762-1:2005), which has been technically revised. It also incorporates the Technical Corrigendum ISO 22762-1:2005/Cor.1:2006. — 84 p. This part of ISO 22762...
Second edition. ISO 22762-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 22762-2:2005), which has been technically revised. It also incorporates the Technical Corrigendum ISO 22762-2:2005/Cor.1:2006. — 62 p. This part of ISO 22762...
Seventh edition. ISO 2285 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This seventh edition cancels and replaces the sixth edition (ISO 2285:2007), which has been aligned with ISO 815-1 and an annex containing a calibration schedule has been added. — 18 p. This International Standard specifies a number of...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 2286-1:1998) , which has been technically revised. — 8 p. This part of ISO 2286 specifies methods of determining the length, width and net mass of a roll of rubber-...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products title, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 2286-2:1998) , which has been technically revised. — 14 p. This part of ISO 2286 specifies methods of determining the total mass per unit area, the mass per...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 2286-3:1998) , which has been technically revised. — 10 p. This part of ISO 2286 specifies a method for the determination, at a specified pressure, of the thickness...
Sixth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This sixth edition cancels and replaces the fifth edition (ISO 2302:2005), which has been technically revised. — 16 p. This International Standard specifies — physical and chemical tests on raw...
Fifth edition. ISO 2303 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 2303:2003). — 20 p. This International Standard specifies, for general-purpose non-oil-extended, solution-polymerized polyisoprene...
Third edition. ISO 2321 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 2321:1983), which has been technically revised. — 32 p. This International Standard specifies methods of test for determining general physical and mechanical properties...
Sixth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This sixth edition cancels and replaces the fifth edition (ISO 2322:2009), which has been technically revised. — 22 p. This International Standard specifies: — physical and chemical tests on raw...
First edition. ISO 23233 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 16 p. This International Standard specifies a method for the determination of the resistance of rubber to abrasion using a driven, vertical abrasive disc (the LAT 100: Laboratory Abrasion Tester 100). The loss in mass on abrasion is...
First edition. ISO 23337 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 20 p. This International Standard specifies a method for the determination of the resistance of rubber to abrasion using the Improved Lambourn test machine. The abrasion loss resulting from the slip caused by the difference in...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 23529:2010), which has been technically revised. — 24 p. This document specifies general procedures for the preparation, measurement, marking, storage, and conditioning or...
First edition. ISO 23711 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 16 p. This International Standard specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in: a) thermoplastic piping systems for non-pressure waste water discharge...
Second edition. ISO 23794 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 23794:2003), of which it constitutes a minor revision designed to update the normative references to reflect the fact that ISO 471, ISO 4648 and ISO 4661-1 cited in Clause 10...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 2393:2008), which has been technically revised. — 30 p. This International Standard specifies the equipment and procedures for the...
Fourth edition. ISO 2439 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This fourth edition cancels and replaces the third edition (ISO 2439:1997 and ISO 2439:1997/Cor.1:1998), which has been technically revised. — 20 p. The indentation hardness of flexible cellular materials is a measure of their...
Third edition. International Standard ISO 2440 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This third edition cancels and replaces the second edition (ISO 2440:1983), which has been technically revised. — 7 p. This International Standard specifies, for flexible and rigid cellular polymeric materials, laboratory procedures which are intended to...
Amendment 1 (15.02.2010) for the third edition of ISO 2440 (15.09.1997). Amendment 1 to ISO 2440:1997 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p.
Second edition. International Standard ISO 2453 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 2453:1975). — 12 p. This International Standard specifies a method for determining the bound styrene content of emulsionpolymerized styrene-butadiene (SBR) rubbers by correlation with the...
Technical corrigendum 1 (15.08.2003) for ISO 2453:1991. Technical Corrigendum 1 to ISO 2453:1991 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 1 p.
Third edition. International Standard ISO 2454 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This third edition cancels and replaces the second edition (ISO 2454:1982), of which it constitutes a minor revision. — 7 p. This International Standard specifies a titrimetric method using ethylemedinitrilotetraacetic acid (EDTA) disodium salt for the...
First edition. ISO 24698-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 12 p. This part of ISO 24698 specifies a method for the determination of the bound acrylonitrile content in NBR by an automatic analyser which uses a combustion process. The method is also applicable to NBR latex. Parts 1 and 2 of this...
First edition. ISO 24698-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 14 p. This part of ISO 24698 specifies a method for the determination of the bound acrylonitrile content in NBR by an automatic analyser which uses the Kjeldahl method. Parts 1 and 2 of this International Standard may not necessarily...
Fourth edition. ISO 247 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 247:1990), which has been revised to update the normative references. — 8 p. This International Standard specifies two methods for the determination of ash from raw rubbers,...
Fourth edition. International Standard ISO 2475 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 2475:1990) which has been technically revised. — 15 p. This International Standard specifies, for...
Sixth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This sixth edition cancels and replaces the fifth edition (ISO 2476:2009), which has been technically revised. — 20 p. This International Standard specifies: — physical and chemical tests on raw...
Fourth edition. ISO 248 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 248:1991), which has been technically revised. — 14 p. This International Standard specifies two methods, a hot-mill method and an oven method, for the determination of...
First editon. ISO 248-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. ISO 248 consists of the following parts, under the general title Rubber, raw — Determination of volatilematter content: - Part 1: Hot-mill method and oven method; - Part 2: Thermogravimetric methods using an automatic analyser with an...
Fifth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 249:2014). — 16 p. This International Standard specifies a method for the determination of the dirt content of raw natural rubber....
First edition. ISO 24999 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 12 p. This International Standard specifies a method for determining the loss in thickness of flexible cellular materials when compressed repetitively to a fixed level of strain. It is particularly useful for quality control in...
Fourth edition. ISO 2781 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 2781:1988), which has been technically revised. It also incorporates the Technical Corrigendum ISO 2781:1988/Cor.1:1996. — 12 p. This International Standard specifies two...
Amendment 1 (15.07.2010) for the fourth edition (01.05.2008) of ISO 2781. Amendment 1 to ISO 2781:2008 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 8 p.
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 2782-1:2012) , which has been technically revised. — 26 p. This part of ISO 2782 specifies three methods for the determination of the permeability to gases of vulcanized or...
Fourth edition. ISO 2878 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 2878:2005), which has been technically revised to include a calibration schedule for the instruments used in the test (see Annex A). — 16 p. This International Standard...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 289-1:2014), which has been technically revised to improve the calibration schedule. — 22 p. This part of ISO 289 specifies a method using a shearing-disc viscometer for...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 289-2:1994), which has been technically revised. — 14 p. This part of ISO 289 specifies a method for determining the pre-vulcanization characteristics of compounded rubber....
First edition (01.11.2003) with correction (01.03.2004). ISO 289-4 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 18 p. This part of ISO 289 specifies a method of use of a shearing-disc viscometer for measuring the Mooney stress-relaxation rate (MSR) of uncompounded or compounded unvulcanized rubbers,...
Fourth edition. ISO 2921 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 2921:1997), which has been technically revised. — 12 p. This International Standard specifies a method for the determination of the temperature-retraction characteristics of...
Fourth edition. ISO 2930 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 2930:1995), which has been technically revised. — 12 p. This International Standard specifies a method for determining the plasticity...
Second edition. ISO 2951 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 2951:1974), which has been technically revised. — 16 p. This International Standard specifies a method for the determination of the insulation resistance of vulcanized and...
Third edition. International Standard ISO 3011 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This third edition cancels and replaces the second edition (ISO 3011:1981), which has been technically revised. — 7 p. This International Standard specifies a method for the determination of the resistance of fabrics coated with rubber or plastics to ozone...
Second edition. International Standard ISO 3136 was developed by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 3136-1975), which has been technically revised. — 3 p. This International Standard specifies a method for the determination of the bound styrene content of styrene-butadiene rubber (SBR) latices.
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 3302-1:1996), which has been technically revised. — 18 p. This part of ISO 3302 specifies classes of dimensional tolerances and their values for moulded, extruded,...
Second edition. ISO 3302-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 3302-2:1998), of which it constitutes a minor revision. — 14 p. This part of ISO 3302 specifies the following geometrical tolerances for moulded and extruded solid...
First edition. ISO 3303-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). Together with Part 2, it cancels and replaces ISO 3303:1990, which has been split into two parts and at the same time technically revised. ISO 3303 consists of the following parts, under the general title Rubber- or plastics-coated...
First edition. ISO 3384-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. It cancels and replaces ISO 3384:2005, which has been technically revised. In addition, the number has been changed to ISO 3384-1. ISO 3384-1 deals with the determination of relaxation in compression at constant temperature, while ISO...
Amendment 1 (15.03.2013) for the first edition (01.12.2011) of ISO 3384-1. Amendment 1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 8 p.
First edition. ISO 3384‑2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 20 p. This part of ISO 3384 specifies two methods for determining the decrease in counterforce exerted by a test piece of vulcanized or thermoplastic rubber which has been compressed to a constant deformation and then undergoes...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products other than hoses. This fourth edition cancels and replaces the third edition (ISO 3385:1989), which has been technically revised. — 18 p. This International Standard specifies a method for the determination of loss in thickness and loss in hardness...
Second edition. International Standard ISO 3386/1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 3386/1-1979), of which it constitutes a minor revision. — 5 p. This pard of ISO 3386 specifies a method for the determination of the compression stress/strain characteristic of low-density...
Amendment 1 (15.04.2010) for the second edition (01.06.1986) of ISO 3386-1. Amendment 1 to ISO 3386-1:1986 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 6 p.
Second edition. International Standard ISO 3386-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 3386-2:1984), of which it constitutes a minor revision. — 8 p. This part of ISO 3386 specifies a method for the determination of the compression stress-strain characteristics of flexible...
Amendment 1 (15.04.2010) for the second edition (15.06.1997) of ISO 3386-2. Amendment 1 to ISO 3386-2:1997 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p.
Third editon. ISO 3387 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 3387:1994), which has been technically revised. — 16 p. This International Standard specifies a test based on hardness measurements for determining the progressive stiffening of...
Fourth edition. The committee responsible for this document is ISO/TC45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 34-1:2010) , which has been technically revised. Precision results from an interlaboratory have been updated as Annex A. — 20 p. This part of ISO 34 specifies three test...
Second Edition. ISO 34-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 34-2:1996), which has been revised principally to update the normative references (ISO 471, ISO 3383 and ISO 4648 have been replaced by ISO 23529). Since ISO 5893 has olso...
Fifth edition. ISO 35 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 35:1995), Clauses 8 and 9 of which have been technically revised. The principal changes are the removal of a number of options for the...
Amendment 1 (01.02.2006) for ISO 35 (15.02.2004, fifth edition). Amendment 1 to ISO 35:2004 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 8 p.
Second edition. International Standard ISO 3582 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 3582:1978), which has been technically revised. — 14 p. This International Standard specifies a small-scale laboratory screening procedure for...
Amendment 1 (01.09.2007) for corrected version (01.08.2003) of the second edition of ISO 3582 (15.12.2000). Amendment 1 to ISO 3582:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p.
Fifth edition. ISO 36 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 36:2005), which has been technically revised. — 12 p. This International Standard specifies a method of test for measuring the force required to separate, by stripping, two plies...
Fifth edition. ISO 37 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 37:2005), which has been technically revised. It also incorporates the Technical Corrigendum ISO 37:2005/Cor.1:2008. — 32 p. This International Standard describes a method for...
Third edition. ISO 3858 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 3858:2004), of which it constitutes a minor revision. — 12 p. This International Standard specifies a method for the determination of...
Fourth edition. ISO 3865 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses.This fourth edition cancels and replaces the third edition (ISO 3865:1997), which has been technically revised. — 14 p. This International Standard specifies three methods for estimating the staining of organic finishes (in the following...
Third edition. ISO 3899 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 3899:1988), of which it constitutes a minor revision the main purpose of which was to update the normative references clause. — 8 p. This International Standard specifies a...
Second edition. International Standard ISO 3900 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 3900:1976), which has been technically revised. — 5 p. This International Standard specifies a method for the...
Second edition. ISO 3934 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 3934:1978), which has been technically revised. — 26 p. This International Standard specifies a system of classification of materials used in preformed gaskets for...
Fifth edition. ISO 4097 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fifth edition cancels and replaces the fourth edition (ISO 4097:2000), which has been technically revised. — 16 p. This International Standard specifies ⎯ physical and chemical tests on raw...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This fourth edition cancels and replaces the third edition (ISO 4633:2002), which has been technically revised. — 18 p. This International Standard specifies requirements for materials used in vulcanized rubber seals for the...
Second edition. ISO 4635 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 4635:1982), which has been technically revised. — 16 p. This International Standard specifies requirements for material for preformed vulcanized rubber joint seals used...
First edition. International Standard ISO 4637 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in April 1978. — 5 p. This International Standard specifies a method for the determination of rubber-to-fabric adhesion under direct tension.
First edition. International Standard ISO 4638 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in February 1982. — 9 p. The air flow permeability of cellular materials indicates, in and indirect manner, some of their structural properties. It may be used to establish correlations between the structure of these...
Second edition. International Standard ISO 4643 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 4643:1980). — 17 p. This International Standard specifies requirements for boots, moulded from poly(vinyl chloride) compounds, for general industrial use. The boots may be either fabric-lined...
Technical corrigendum 1 (01.06.1991.) for ISO 4645:1984. Technical corrigendum was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 2 p.
First edition. International Standard ISO 4645 was prepared by Technical Committee 45, Rubber and rubber products. — 8 p. This International Standard describes two methods for the detection and identification, by thin layer chromatography, of antidegradants, which may be present in raw rubber, unvulcanized compounded rubber, or rubber products.
Second edition. International Standard ISO 4646 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 4646:1978), clauses 3, 7 and 8 of which have been technically revised. — 9 p. This International Standard specifies a procedure for determining the lowest temperature at which fabrics coated...
Second edition. SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 4647:1982), which has been technically revisedprimarily concerning updating the references, including a reference to ISO 5893 for the apparatus, updating the test report format and the addition of a calibration schedule. — 20 p. This International Standard specifies a...
Third edition. ISO 4649 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 4649:2002), which has been technically revised. — 24 p. This International Standard specifies two methods for the determination of the resistance of rubber to abrasion by means...
Third edition. ISO 4650 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 4650:2005), which has been technically revised. — 94 p. This International Standard specifies two methods for the identification of rubbers, including thermoplastic elastomers,...
Second edition. International Standard ISO 4651 ws prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 4651:1979), which has been technically revised. — 13 p. This International Standard spedifies the procedure for determining the dynamic cushioning performance of cellular rubber materials and...
Amendment 1 (15.09.2006) for ISO 4651 (01.12.1988). Amendment 1 to ISO 4651 ws prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 6 p.
Second edition. ISO 4652 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition of ISO 4652 cancels and replaces ISO 4652‑1:1994, which has been technically revised. — 34 p. This International Standard specifies four methods for the determination of the...
Second edition. ISO 4656 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 4656:2007), which has been technically revised. — 24 p. Oil absorption number (OAN) is a measure of the ability of a carbon black to...
Third edition of ISO 4658 (01.12.1999) with Amendment 1 (15.10.2004). International Standard ISO 4658 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second (ISO 4658:1990), which has been technically revised. Amendment 1 to...
Sixth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This sixth edition cancels and replaces the fifth edition (ISO 4659:2003), which has been technically revised. — 14 p. This International Standard specifies the following: — physical and chemical...
Fourth edition. ISO 4660 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 4660:1999), which has been technically revised. — 12 p. This International Standard specifies a method of determining the colour of...
First edition. International Standard ISO 4661-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 4 p. This part of ISO 4661 includes a number of factors of importance in the preparation of samples for chemical testing, in order to ensure the best use of the relevant ISO methods of test.
Third edition. ISO 4662 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 4662:1986), which has been technically revised. — 38 p. This International Standard specifies two methods for determining the rebound resilience of rubber the hardness of which...
Technical Corrigendum 1 (15.03.2010) for ISO 4662:2009. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 1 p.
Second edition. ISO 4664-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 4664-1:2005), which has been technically revised. — 30 p. This part of ISO 4664 provides guidance on the determination of dynamic properties of vulcanized and thermoplastic...
First edition. ISO 4664-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. It cancels and replaces ISO 4663:1986, of which it constitutes a technical revision. — 18 p. This part of ISO 4664 specifies methods, using a torsion pendulum, of determining the dynamic properties in shear, that is the shear modulus and...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.This third edition cancels and replaces the second edition (ISO 4665:2006) , which has been technically revised. — 18 p. This International Standard specifies methods for the exposure of vulcanized or thermoplastic rubbers to natural or...
Second edition. ISO 4666-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 4666-1:1982), which has been technically revised. — 16 p. This part of ISO 4666 establishes general principles for flexometer testing and defines the terms used. Flexometer...
Second edition. ISO 4666-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 4666-2:1982), of which it constitues a minor revision. — 14 p. This part of ISO 4666 specifies a rotary flexometer test for the determination of the temperature rise and...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 4666-3:2010) , 5.1.2 of which has been technically revised. — 24 p. This document specifies the flexometer test with constant-strain amplitude for the determination of the...
First edition. ISO 4666-4 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 26 p. This part of ISO 4666 specifies a constant-stress flexometer test for the determination of the temperature rise and resistance to fatigue of vulcanized rubbers. Many rubber products, such as tyres and belts, are tested by...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 4674-1:2003) , which has been technically revised. — 20 p. This part of ISO 4674 specifies two methods for determining the forces necessary to initiate and propagate...
First edition. International Standard ISO 4674-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. Together with part 1 of ISO 4674, this first edition of ISO 4674-2 cancels and replaces the first edition of ISO 4674 (ISO 4674:1977), which has been technically revised. — 12 p. This part of this ISO 4674 describes a method for the determination of tear...
Second edition. International Standard ISO 4675 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 4675:1979), of which it constitutes a technical revision. — 8 p. This International Standard specifies a method for determining the ability of fabrics coated with rubber or plastics to resist...
Fifth edition. ISO 48 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 48:2007), of which it constitutes a minor revision intended to update the precision statements in Annex B. It also incorporates the Technical Corrigendum ISO 48:2007/Cor.1:2009....
First edition. International Standard ISO 5423 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 18 p. This International Standard specifies requirements for boots, moulded from polyurethane compound, for general industrial use. The boots may be either fabric-lined or unlined and of any style from ankle boots to full thigh height inclusive
Fourth edition. ISO 5435 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 5435:1994), which has been technically revised to include two additional types of test equipment and precision data. — 20 p. This...
First edition. ISO 5470-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 12 p. This part of ISO 5470 details two separate methods for determining the resistance of a material to wet and dry abrasion. It is applicable to the coated surface or surfaces of coated fabrics. If the abrasion behaviour of the...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 5470-1:1999) which has been technically revised. — 16 p. This part of ISO 5470 describes a method of assessing the abrasive wear resistance of coated fabrics using the Taber abrader.
Second edition. International Standard ISO 5473 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 5473:1979), which has been technically revised. — 7 p. This International Standard specifies a method for determining the crush resistance of fabrics coated with rubber or plastics. The method...
Fourth edition. ISO 5600 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 5600:2007), of which it constitutes a minor revision designed to add a calibration schedule (see Annex A). — 12 p. This International Standard specifies a method for the...
Third edition. ISO 5603 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 5603:2007), of which it constitutes a minor revision designed to add a calibration schedule (see Annex A). — 22 p. This International Standard specifies two methods for...
Second edition. International Standard ISO 5794-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 5794-2:1982), which has been technically revised. — 8 p. This part of ISO 5794 specifies the test...
First edition. ISO 5794‑3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This part of ISO 5794 specifies the test formulation, equipment, procedure and test methods for determining the physical properties of precipitated hydrated silica in a compound based on a...
Second edition. International Standard ISO 5796 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 5796:1990), of which it constitutes a technical revision. — 25 p. This International Standard specifies the...
First edition. International Standard ISO 5892 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in August 1979. — 7 p. This International Standard specifies material requirements for preformed, solid vulcanized rubber structural gaskets used in sealing applications where both resistance to stress relaxation and...
Third edition. ISO 5893 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. This third edition cancels and replaces the second edition (ISO 5893:1993), which has been technically revised. — 12 p. This International Standard specifies requirements for tensile-testing systems operating at constant rate of traverse...
Second edition. International Standard ISO 5978 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 5978:1979), of which it constitutesa minor technical revision. — 8 p. This International Standard specifies a method for the determination of the resistance or rubber- or plastics-coated...
First edition. International Standard ISO 5979 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in January 1981. — 5 p. This International Standard specifies a method of characterizing the flexibility of some rubber or plastics coated fabrics.
Third edition. ISO 5981 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 5981:1997), which has been technically revised. — 16 p. This International Standard specifies two methods of evaluating the resistance to combined shear flexing and...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 5999:2007), which has been technically revised. — 22 p. This International Standard specifies requirements for flexible load-bearing polyurethane foam of the polyether...
Third edition. ISO 6072 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 6072:2002), which has been technically revised. — 26 p. This International Standard specifies test methods for evaluating the effect of hydraulic fluids on standard...
Second edition. International Standard ISO 6101-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6101-1:1981), of which it constitutes a technical revision. — 9 p. This part of ISO 6101 specifies an atomic absorption spectrimetric method for the determination of the zinc content of rubbers.
Second edition. International Standard ISO 6101-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6101-2:1986), which has been technically revised. — 12 p. This part of ISO 6101 specifies an atomic absorption spectrometric method for the determination of the lead content of rubbers.
Second edition. International Standard ISO 6101-3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6101-3:1988), which has been technically revised. — 12 p. This part of ISO 6101 specifies an atomic spectrometric method for the determination of the copper content of rubbers.
Second edition. International Standard ISO 6101-4 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6101-4:1988), which has been technically revised. — 12 p. This part of ISO 6101 specifies an atomic absorption spectrometric method for the determination of the manganese content of rubbers.
Second edition. ISO 6101-5 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 6101-5:1990), which has been revised to update the normative references. — 12 p. This part of ISO 6101 specifies an atomic absorption spectrometric method for the...
First edition. ISO 6101-6 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 14 p. This part of ISO 6101 specifies an atomic absorption spectrometric method for the determination of the magnesium content of natural rubber latex concentrate, raw natural rubber and products made from natural rubber.
Second edition. International Standard ISO 6110 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6110:1982), of which it constitutes a technical revision. — 5 p. This International Standard specifies requirements for lined or unlined moulded poly(vinil chloride) (PVC) industrial boots,...
Second edition. International Standard ISO 6112 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6112:1982), of which it constitutes a technical revision. — 5 p. This International Standard specifies requirements for lined or unlined moulded poly(vinyl chloride) (PVC) industrial boots,...
First edition. International Standard ISO 6123/1 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in January 1981. — 5 p. This part of ISO 6123 specifies requirements for the measured hardness of rubber or plastics covered rollers.
First edition. International Standard ISO 6123/3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 8 p. This part of ISO 6123 specifies classes of dimentional tolerances for rubber- or plastics-covered rollers and tests methods for the measurement of dimensions.
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 6123-2:1988) , of which it constitutes a minor revision to update the normative references. — 14 p. This part of ISO 6123 establishes a classification of rubber or...
Second edition. International Standard ISO 6133 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Physical and degradation tests. This second edition cancels and replaces the first edition (ISO 6133:1981), which has been technically revised (two additional methods, E and F, have been included). — 8 p. This International Standard...
Fourth edition. ISO 6179 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 6179:1998), of which it constitutes a minor revision intended to update the normative references (ISO 471 and ISO 4648 have been replaced by ISO 23529). — 12 p. This...
Fourth edition. ISO 6209 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 6209:1988), which has been technically revised. — 14 p. This International Standard specifies a method for the quantitative...
Second edition. ISO 6225-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 6225-1:1984), which has been revised to update the normative references. — 10 p. This part of ISO 6225 specifies a thin-layer chromatographic method for the determination of...
Third edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 6235:1995) , of which it constitutes a minor revision. — 10 p. This International Standard specifies a method for the determination...
First edition. International Standard IS0 6446 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Miscellaneous products. — 12 p. This International Standard specifies requirements for rubber materials used in elastomeric bridge bearings, which may be of the plain-pad or laminated type. Italso specifies methods of test and describes...
First edition. ISO 6450 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 16 p. This International Standard specifies two methods (methods 1 and 2) of evaluating the resistance of fabrics coated with plastics or with vulcanized rubber to the action of liquids by measurement of selected properties of the...
First edition. International Standard ISO 6451 was developed by Technical Committee ISO/TC 45, Rubber and rubber products, and was circulated to the member bodies in November 1980. — 3 p. This International Standard specifies a rapid method for checking the fusion of polyvinyl chloride (PVC) coatings on coated fabrics.
Second edition. ISO 6452 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 6452:2000), which has been technically revised. — 20 p. This International Standard specifies a test method which is intended to determine the fogging characteristics...
First edition. International Standard ISO 6453 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 8 p. This International Standard specifies requirements for flexible cellular PVC in the form of sheets up to 100 mm in thickness for use in applications involving dielectric (HF) welding (for example padding and quilting).
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 6505:2005), which has been technically revised. — 20 p. This International Standard specifies a method for the determination of the tendency of vulcanized or thermoplastic...
Fourth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 6914:2008), which has been aligned with ISO 23529 and completed with details regarding dimensions, test equipment and methods. — 16 p. This International Standard describes...
Second edition. International Standard ISO 6915 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 6915:1984), of which it constitutes a minor revisiion. — 9 p. The International Standard specifies the minimum requirements for flexible polyurethane foams up to and including 20 mm thick...
Amendment 1 (15.05.2007) for the first edition of ISO 6916-1 (15.07.1995). Amendment 1 to ISO 6916-1:1995 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 8 p.
Technical corrigendum 1 (15.05.2002) forISO 6916-1:1995. Technical Corrigendum 1 to International Standard ISO 6916-1:1995 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 1 p.
First edition. ISO 6916-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 24 p. This part of ISO 6916 classifies flexible cellular rubber products known as sponge and expanded rubber. The base material used in their manufacture may be natural rubber, reclaimed rubber, synthetic rubber or rubber-like...
Third edition. ISO 6943 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 6943:2007), which has been revised primarily to include a calibration schedule for the apparatus used (see Annex B). — 24 p. This International Standard describes a method for...
Fourth edition. ISO 706 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 706:1985), Clauses 6 and 8 of which have been technically revised. In addition, a precision statement and an informative annex...
First edition. International Standard ISO 7229 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 7 p. This International Standard specifies a method of measuring gas transmission through fabrics coated with plastics or rubber, a property known as permeability.
Second edition. ISO 7231 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 7231:1984), which has been technically revised. — 16 p. This International Standard specifies two methods for determining the air flow value of flexible cellular...
Second edition. International Standard ISO 7269 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 7269:1987), of which it constitutes a minor revision. — 13 p. This International Standard specifies three methods for the determination of free sulfur in vulcanized rubber: two versions of the...
Technical Corrigendum 1 (15.05.2002P for ISO 7269:1995. Technical Corrigendum 1 to International Standard ISO 7269:1995 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 1 p.
First edition. ISO 7270 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. This part of ISO 7270 cancels and replaces ISO 7270:1987, which has been technically revised. — 60 p. This part of ISO 7270 specifies a method for the identification of polymers, or blends of polymers, in raw rubbers and in vulcanized or...
Amendment 1 (15.07.2010) for ISO 7270-1 (15.04.2003). Amendment 1 to ISO 7270-1:2003 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 8 p.
Second edition. ISO 7270-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 7270-2:2005), which has been technically revised. — 16 p. This part of ISO 7270 specifies a pyrolytic gas-chromatographic method for the determination of the...
Second edition. ISO 7323 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 7323:1985), which has been revised to update the normative references (ISO 471 and ISO 3383 have been replaced by ISO 23529 and ISO 1796 by ISO 1795). It also incorporates the...
Third edition. ISO 7617-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 7617-1:1994), which has been technically revised. — 22 p. This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for...
Third edition. ISO 7617-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and replaces the second edition (ISO 7617-2:1994), which has been technically revised. — 14 p. This part of ISO 7617 specifies requirements for coated fabrics for upholstered furniture, manufactured by...
First edition. International Standard ISO 7617-3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 8 p. This part of ISO 7617 specifies requirements for polyurethane-coated fabrics for upholstered runiture, manufactured by applying to one side of a woven textile fabric a substantially continuous coating of a suitable polyurethane composition.
Fourth edition. ISO 7663 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 7663:1995), which has been technically revised. — 14 p. This International Standard specifies: ⎯ physical and chemical tests on raw...
First edition. International Standard ISO 7664 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This first edition cancels and replaces ISO/TR 7664:1984, which has been technically revised. — 7 p. This International Standard provides information on the most suitable...
First edition. International Standard ISO 7725 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 11 p. This International Standard specifies methods for the determination of chlorine and/or bromine present in raw rubber, uncured mixes or vulcanizates.
Fourth edition. ISO 7743 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 7743:2008), which has been technically revised. — 28 p. This International Standard specifies methods for the determination of the compression stress-strain properties of...
Second edition. International Standard ISO 7780 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 7780:1978) which has been technicallly revised. — 14 p. This International Standard specifies photometric methods for the determination of manganese, after oxidation with sodium periolate, in...
Fourth edition. ISO 7781 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fourth edition cancels and replaces the third edition (ISO 7781:2001), which has been technically revised. — 12 p. This International Standard specifies methods for the determination of the soap and organic-acid content of raw...
Second edition. International Standard ISO 7854 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products.This second edition cancels and replaces the first edition (ISO 7854:1984), which has been technically revised. — 16 p. This International Standard describes three methods of assessing the resistance of coated fabrics to damage by repeated flexing.
Third edition. ISO 8013 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This third edition cancels and replaces the second edition (ISO 8013:2006), which has been technically revised. — 26 p. This International Standard specifies a method for the determination of creep in vulcanized rubber continuously...
Second edition. International Standard ISO 8053 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. This second edition cancels and replaces the first edition (ISO 8053:1986), of which it constitutes a minor revision. — 9 p. This International Standard specifies a photometric method for the determination of trace amounts of copper in raw rubber, latices...
Second edition. ISO 8067 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 8067:1989), which has been technically revised to include a second method, using an angle test piece, in addition to the existing method which uses a trouser test...
First edition. International Standard ISO 8095 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products. — 8 p. This International Standard specifies requirements for fabric coated on one or both sides with a suitably plasticized coating, pigmented or otherwise, of poly(vinyl chloride) (PVC) or copolymer the major constituent of which is vinyl chloride and...
First edition. ISO 8096 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). It cancels and replaces ISO 8096-1:1989, ISO 8096-2:1989 and ISO 8096-3:1988, which have been technically revised and combined into a single document. — 28 p. This International Standard specifies the requirements for water vapour...
Technical Corrigendum 1 to ISO 8096:2005 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). — 1 p.
Second edition. ISO 812 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 812:1991), which has been technically revised. — 16 p. This International Standard specifies a method for determining the lowest temperature at which rubber materials do not...
Fifth edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 813:2010) , of which it constitutes a minor revision concerning an update of the normative references. — 16 p. This International Standard specifies a method for the...
Fifth edition. ISO 814 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This fifth edition cancels and replaces the fourth edition (ISO 814:2007), of which it constitutes a minor revision to include an annex specifying a calibration schedule for the apparatus used. — 12 p. This International Standard specifies a...
Second edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 815-1:2008), which has been technically revised, mainly by addition of a calibration schedule (Annex B). — 18 p. This part of ISO 815 specifies methods for the determination...
Second edition. ISO 8307 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 8307:1990), which has been technically revised. — 12 p. This International Standard specifies a method for determining the resilience by ball rebound of flexible...
First edition. International Standard ISO 8312 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. It cancels and replaces ISO 8312-1:1988, which has been technically revised. — 26 p. This International Standard defines stearic acid (including blends of stearic and palmitic...
Fourth edition. ISO 8332 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This fourth edition cancels and replaces the third edition (ISO 8332:2006) which has been technically revised. — 32 p. This International Standard specifies methods of test for determining the main...
Third edition. ISO 8511 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This third edition cancels and replaces the second edition (ISO 8511:1995), of which it constitutes a minor revision. — 12 p. Carbon black for the rubber industry is generally pelletized to reduce...
First edition. ISO 8942 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. It cancels and replaces ISO/TR 8942:1988, which has been technically revised. — 14 p. This International Standard specifies two methods for the determination of the individual pellet crushing...
Second edition. This second edition cancels and replaces the first edition (ISO 9026:1991), which has been revised to update the normative references (ISO 471, ISO 3383 and ISO 4648 have been replaced by ISO 23529 and ISO 1796 by ISO 1795). In addition, the list of usable test pieces in 6.1 has been extended with the addition of the type 1A dumbbell and the text has been...
Second edition. ISO 9028 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This second edition cancels and replaces the first edition (ISO 9028:1989), which has been revised to update the normative references. — 10 p. This International Standard specifies methods for desentegration of raw rubber and rubber...
First edition. International Standard ISO 9298 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This International Standard specifies the methods to be used for the evaluation of zinc oxide for use in the rubber industry.
Second edition. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. This second edition cancels and replaces the first edition (ISO 9298:1995) , which has been technically revised. — 18 p. This document specifies the methods to be used for the evaluation of...
Second edition. ISO 9631 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO 9631:1991), which has been technically revised. — 18 p. This International Standard specifies requirements for materials used in vulcanized-rubber seals for hot potable...
First edition. International Standard IS0 9691 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, SubCommittee SC 4, Miscellaneousproducts. — 16 p. This International Standard describes and classifies imperfections in rubber joint rings for pipelines.
Third edition. ISO 976 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry, in close collaboration with ISO/TC 61, Plastics and ISO/TC 35, Paints and varnishes. This third edition cancels and replaces the second edition (ISO 976:1986), as well as the second edition of ISO...
Amendment 1 (01.02.2006) for the third edition of ISO 976:1996. Amendment 1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 8 p.
Second edition. International Standard ISO 9924-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. This second edition cancels and replaces the first edition (ISO 9924-1:1993), which has been technically revised. — 14 p. This part of ISO 9924 specifies a thermogravimetric method for the determination of the...
First edition 2000-09-01. International Standard ISO 9924-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analyses. — 14 p. This part of ISO 9924 specifies a thermogravimetric method for determining the total organic content, carbon black content, carbonaceous residue and ash in vulcanizates and uncured compounds...
Amendment 1 to ISO 9924-2:2000 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 6 p.
First edition. ISO 9924-3 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. — 22 p. This part of ISO 9924 specifies a thermogravimetric method for the determination of the main constituents of rubber compounds such as elastomer(s), carbon black and mineral filler. It establishes the “fingerprint” of the tested...
First edition. ISO/TR 16098 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This Technical Report specifies standard materials, standard test formulations, equipment and processing methods for evaluating the dispersion of reclaimed rubbers and reclaimed crumb...
First edition. ISO/TR 16314 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This Technical Report provides a method for the selective determination of polyaromaticity of oil in reclaimed rubbers. The method is based on nuclear magnetic resonance (NMR) spectrometry.
Second edition. ISO/TR 7620 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This second edition cancels and replaces the first edition (ISO/TR 7620:1986), which has been technically revised. — 42 p. This Technical Report describes a classification system for the reporting and tabulation of the chemical...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This Technical Specification defines — the physical and chemical tests on raw reclaimed natural rubber, and — the standard materials, standard test formulations, equipment, and processing...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 12 p. This Technical Specification specifies — physical and chemical tests on raw reclaimed isobutene-isoprene (IIR) rubber, and — standard materials, standard test formulations, equipment, and...
First edition. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry. — 14 p. This Technical Specification specifies physical and chemical tests, standard test formulations, equipment and processing methods for the vulcanization-characteristics evaluation and the...
Комментарии