Report NMAB-270 of the Committee on Gun Tube Technology. 1971. – 83 p. The object of the study was to recommend long-range improvements in the manufacture and concept of gun barrels, as well as to suggest solutions to current gun manufacturing problems. Improved steels are listed and coatings for the bore proposed, which might result in better performance or lower cost....
Scientific paper. Applied Thermal Engineering 28 (2008), pp. 881-888. When firing, large amounts of heat flow into the gun bore surfaces and result in wear and erosion of the gun bore. Moreover, the chamber surface temperature will reach the cook-off temperature of propellant during long sustained firing, which will impact on user safety and facilities. For large-caliber gun, a...
Dover, New Jersey: Large caliber weapon systems laboratory. 1983.
The erosion resistance of tungsten/carbon and tantalum/tungsten deposited on AISI 4340 steel and molybdenum substrate were investigated. Erosion data acquired with the ARRADCOM test device indicated poor adhesion between each refractory metal coating and 4340 steel. Mechanical failure of the molybdenum substrate...
Reports. National defense research committee. Reports No. A-90, A-91: progress reports. Shortly after Section A of Division a was constituted for the purpose of attacking the problem of gun erosion and other aspects of hyper-velocity, and the facilities of the Geophysical Laboratory of the Carnegie Institution of Washington were made available for this work, Dr. John S. Burlew...
Scientific report. ARL-TR- 2473. Army Research Laboratory. Aberdeen Proving Ground, MD, 2001. – 41 p. Barrel heating and erosion concerns for the Navy are being brought to light by new extended-range munitions. These munitions have, in general, higher performance requirements and use new propellants. In light of these concerns, the following investigation was performed to...
U.S. Naval Proving Ground report No .1532. U.S. Naval Proving Ground. Dahlgren, Virginia, 1957. – 88 p. A lot of 5"/54 NACO (Navy Cool) flashless propellant was evaluated with respect to erosion characteristics in rapid fire schedules. Erosion was reduced by a factor of three relative to the standard pyro powder. Abstract. Foreword. Description of Material. Description of Test...
Watervliet, New York: US Army Benet Laboratories. 1995
The first known gun barrel thermochemical erosion modeling code is presented. Ibis modeling code provides the necessary missing element needed for developing a generalized gun barrel erosion modeling code that can provide analysis and design information that is unattainable by experiment alone. At the current stage of code...
DARCOM pamphlet No. 706- 253. Alexandria, 1979, -250 p. This handbook is devoted to a description of a rational design sequence and methodology needed to take a particular breech mechanism from conception — as prompted by military needs and technical requirements generated for a given weapon—to the stage of acceptance and production. Major divisions of the handbook provide...
Report No. 1192. Ballistic research laboratories. 1963, - 55 p. Data on temperature distribution and heat input in a 37mm gun during firing are presented. These results are discussed and compared with theoretical values obtained by using the Nordheim, Soodak and Nordheim method of calculation. Abstract. Experimental procedures. Data and results. Comparison with the theory of...
Report of committee on gun tube erosion. AD-A01 7- 104. National Materials Advisory Board (NAS-NAE). Washington, D.C. 1975. -38 p. The erosion of gun tubes is a very complex interdisciplinary problem involving several branches of engineering and science. Several mechanisms are responsible for this limitation to gun tube life, some of which are of thermal origin, some are...
International Conference on Applied Mechanics, Mechanical and Materials Engineering (AMMME 2016). — 6 p. This paper aims at gun erosion under the condition of periodic thermal shock during firing. Firstly, the mathematical model with two-dimensional heat conduction for gun barrel was established. Secondly, finite difference equations of internal nodes were derived by using ADI...
Тепловая хрупкость стали 175-мм пушечных труб. Technical Report AMMRC TR 69-16, Army materials and mechanics research center. 1969. – 18 p. Sections of two 175-mm M113 gun tubes were utilized to study the development of both reversible and irreversible temper brittleness in 3 percent nickel-chromium gun steel. Relative material toughness indicated by the 100 percent fibrous...
(Греко В. Питер. Эрозия в 81-мм минометных труб).
Report. Watervliet, N.Y.: Large Caliber Weapon System Laboratory. 1977. – 40 p.
A laboratory erosion tester has been designed and developed for predicting the service performance of protective coating materials in the bores of mortar systems using rounds with tail fins. Due to the use of newly designed ammunition, the service...
Proceedings of the Interservice Technical Meeting. February 25 - 26, 1970. Watervliet Arsenal. Watervliet, New York. 1970. – 533 p. The specification of performance characteristics for conventional weaponry is of considerable interest and concern to the organizations utilizing such equipment. As might be expected, one of the primary considerations is the stipulation of the safe...
Report No 804. US naval proving ground, Virginia, 1951, - 13 p. This is the report on a study of the action of a gun barrel during the passage of the projectile through it's bore. It covers the exploratory phase of two research problems: - vibrations of gun barrels; - vibratory flight and engraving of projectile.
Weapon Systems and Technology Directorate Armament Engineering and Technology Center U.S. Army Armament Research, Development and Engineering Center., Document RTO-MP-AVT-109. 2004. -15 p. Wear and erosion – is one of several failure mechanisms that can cause large caliber Gun Barrels to be condemned and removed from service. This paper describes the phenomenon, its causes and...
U.S. Naval proving ground. 1954.
A rapid fire life test has been conducted in 3''/70 caliber gun Type C Mod 2 Serial No. 24483 employing a cool double base picrite propellant# The results of this test were reported in reference. The Bureau of Ordnance has directed that a similar test in a similar barrel employing a cool single base non-picrite propellant be conducted in order...
Technical report AMCMS No. 501A .11.84400. DA Project No. 1T061101A91A. Benet Weapon Laboratory. Watervliet Arsenal. Watervliet, New York. Gun cube erosion can be defined as the bore surface damage and bore enlargement caused by firing, which can lead to loss in accuracy and the effectiveness of the weapon. It is one of the two major factors on the basis of which gun tubes are...
Warszawa: Przegląd Artyleryjski, 1929. — 272 s. Прочность стволов артиллерийского и стрелкового оружия. W polskiej wojskowej literaturze fachowej techniczno-artyleryjskiej dawał się odczuć brak podręcznika, dotyczącego konstrukcji luf działowych ujętej z punktu widzenia ich wytrzymałości; poszczególne zagadnienia z tej dziedziny były niejednokrotnie poruszane na łamach...
International journal of mechanics, Issue 4, Volume 5, 2011, -8 p. The paper provides results of an analysis of character of smooth barrel bore wear of the T-72 tank, a combat vehicle that remains in service with a number of armed forces throughout the world. The BG20 MkII Gun Barrel Bore Gauge system purchased from Aeronautical & General Instruments Ltd in the UK was used to...
Weapons Systems Division Defense Science and Technology Organization. DSTO-TR-1757, 2005, -48 p. The Australian Defense Force will soon have to contend with gun barrel erosion issues arising from the use of new low-vulnerability gun propellants, the acquisition of new ammunition and gun systems, and possible modifications to existing propelling charge designs. A critical,...
Scientific paper. Raytheon Company. Missile Systems Division. Bedford, Massachusetts. – 4 p. The bore erosion process in a gun barrel has been simulated using the Advanced Continuous Simulation Language (ACSL). The validity of this model has been proven through comparison with actual firing range data. Data representative of the class of gun, but not associated with any...
Technical report BRL-TR-2996, Ballistic research laboratory Aberdeen Proving Ground, Maryland, 1989, - 21 p. Modern US projectiles incorporate plastic obturator bands to reduce the ill effects of high temperature gas escaping from behind the projectile. Not all NATO countries use obturators on their projectiles. Currently several of these countries are considering introducing...
(Крупский C.И., Тейлор Б.Р., Аудино Ф.И. Измерение шага нарезов в артиллерийских стволах).
Technical report. Watervliet, N.Y.: Watervliet arsenal. 1976. – 29 р. (англ. яз.)
Methods presently employed for determining conformance of rifling twist in gun tubes do not provide for direct measurement. The machine tooling used in manufacturing is calibrated and it is assumed the...
Without input dates. Documents in PDF-format. – 5 p. Приведена информация о лазерных устройствах картографирования поверхности артиллерийских стволов. Оборудование возможно использовать для контроля живучести орудийных стволов. Производитель оборудования - Laser Techniques Company.
Aberdeen Proving Ground, Maryland: Ballistic Research Laboratory. June 1982. The subject program is part of a continuing effort to identify distinct mechanisms that contribute to gun barrel wear and erosion. The thermochemical effects of altering the CO/CO2 ratio of a propellant gas in a gun tube was the main topic for investigation in this program. Experiments were conducted...
Royal Armament Research and Development Establishment R.A.R.D.E. Memorandum 8/67, 1967. – 21 p. This report gives details of the examination of pitted barrels and concludes that the major cause of pitting is corrosion of the bores by decomposition products of the bomb obturating rings. Provisional trials with Polycarbonate obturating rings are described. It is considered that...
Ballistic Research Laboratory. Aberdeen Proving Ground, Maryland, 1991, - 53 p. Heating of a gun barrel by repeated firing is modeled in a computer program that solves the one-dimensional (radial) unsteady heat conduction equation by a second-order finite-difference procedure. Coupling with interior ballistics is accomplished by employing as input data the bore temperature and...
Technical report ARCCB-TR- 03016. US Army ARDEC. Benêt Laboratories. Watervliet Arsenal, NY, 2003, - 23 p. The objective of the study was to gain further insights into the origin of chromium loss in tank guns. The present report summarizes the results of a study surveying chromium loss at various critical locations along a 120-mm M256 tank gun tube. Tube no. 6824 was selected...
Technical report WVT-TR- 74033. Benet Weapons Laboratory. Watervliet Arsenal, Watervliet, N.Y. 1974, - 33 p. One difficulty in the wear prediction in new cannon systems is the uncertainty in its service life criteria. For tubes with low erosion rate, the service life is generally fatigue limited, and in tubes with high erosion rate the service life is limited by the accuracy of...
Technical report WVT-TR- 75017. Watervliet Arsenal. Watervliet, New York, 1975, - 14 p. Two tubes were examined metallographically as part of the fatigue testing program being conducted at the Watervliet Arsenal for the Naval Weapons Lab NWL), Dahlgren, VA. One tube, No. 52, was fired 1590 rounds with NACO, while the other tube, No. 7, was fired 1500 rounds with PYRO as the...
Memorandum report ARBRL-MR- 02952. US army armament research and development command. Ballistic research laboratory. Aberdeen proving ground, Maryland. 1979, - 26 p. The 155mm XM201E2 is a dual zone propelling charge that has been in engineering development for the past several years. The XM201E2, as part of a new family of charges, was also intended as a replacement for the...
Technical report AD-A020 639. Naval Surface Weapons Center. Dahlgren Laboratory, Virginia. 1975, - 24 p. Results from an elementary heat transfer analysis show that certain bore coatings, on the order of 10 piu in thickness and acting only as insulative thermal barriers, can reduce bore surface heat transfer to levels significantly below that present in gun barrels having no...
Thessis. — Hartford, Connecticut: Rensselaer Polytechnic Institute, 2012. — 55 с. (на англ. яз.) Политехнический институт Ренсселера (Rensselaer Polytechnic Institute). Специальность: инженерия (Engineering science). Коррозионные изменения в материалах ствола автоматической пушки M242 в условия. Firearms operated by the military are often exposed to aggressive environments, and...
Watervliet, NY: US Army Armament Research, Development And Engineering Center
Erosion modeling predictions are given for the current M829E3 round configuration and weighted averages per temperature for the computer correction factor (CCF). Our gun erosion model was developed through a ten-year joint partnership with Software and Engineering Associates, Inc., Carson City, NV....
N.Y. Watervliet: US Army Armament Research, Development and engineering center. 1998.
As our gun erosion database increases for in-service and out-of-service 120-mm M256 tubes with M829Ax series rounds, distinct erosion patterns and mechanisms are emerging. Variability exists for M256 guns with M829Ax series rounds depending on round count, round type, round-conditioning...
(Сопок Сэм. 120мм M830A1 прогноз живучести стволов при нагреве).
Technical Report. -Watervliet, NY: Benet Laboratories, 2009, - 14 р.
A wear life prediction is given for the US Army’s M830A1 HEAT round used in the 120mm M256 & XM360 cannons. Five predictions are required and provided for the fielding of the 120mm FCS MCS gun system. Four of these predictions are for the hot,...
Translated from Russian. Proizvodstvo artilleriyskikh sistem. (Mekhanicheskaya Obrabotka Oruiynykh Stvolov). 1972. – 353 p. Manufacture of tube artillery weapons is discussed. Emphasis is placed on manufacture of weapon tubes, beginning with a forging and ending with a finished tube, ready for installation and deployment. Some discussion is present on other parts of the weapon....
Proceedings of symposium. 29-31 March 1977. – 721 p. This volume consist of the technical papers presented at the Tri-Service Gun Tube Wear and Erosion Symposium, held a.t the Picatinny Arsenal, Dover, New Jersey, on March 28-31 1977. It was the first Tri-Service Symposium hosted at the newly formed Army Armament Research id Development Command (AKKADCOM). The objective of this...
Proceedings of symposium. 25-27 October 1982. – 565 p. This volume consists of reprints of the technical papers presented at the Tri-Service Gun Tube Wear and Erosion Symposium, held at Picatinny Arsenal, Dover, New Jersey, on October 25-27, 1982, but was updated to reflect the current findings. It was the second Tri-Service Symposium hosted at the Army Armament Research and...
U.S. Army Materiel Command pamphlet. Research and development of materiel engineering design handbook. Headquarters. U. S. Army Materiel Command, 1964. – 113 р. Орудийные стволы. Освещены принципы построения, конструкции и функционирования артиллерийских стволов. Regions of the gun tube. Types of gun tubes. Firing phenomena affecting gun tubes. Ways of minimizing harmful...
U.S. Army Materiel Command pamphlet. Research and development of materiel engineering design handbook. Headquarters. U. S. Army Materiel Command, 1968. – 138 р. Надульные устройства артиллерийского ствола. Освещены принципы построения, конструкции и функционирования дульных тормозов для артиллерийских стволов. Сontents: Muzzle gas flow Muzzle brakes Blast deflectors Flash...
Technical Report. US Army Armament Command Rock Island, Illinois. 1975, -21 p. A mechanism for the decoppering action of metallic lead on gun tubes is proposed in which it is assumed that lead melts, dissolves the deposited copper, and carries the copper out in the liquid. The proposed mechanism is shown to be reasonable based on the properties of lead and considering the...
Final report. Generai Thomas J. Rodman laboratory Rock Island arsenal, Rock Island, Illinois, 1977, -189 p. An analysis was conducted on the performance of M16A1 rifles made by three manufacturers with the use of two kinds of ammunition and three rates of fire. A data include extreme spread and here erosion gage measurements, each as a function of the number of rounds fired....
Учебное пособие. — СПб.: Балтийский государственный технический университет "Военмех" им. Д.Ф. Устинова (БГТУ), 2007. — 79 с. — ISBN: 5-85546-286-2. Пособие, соответствующее курсам «Колебания стволов артиллерийских орудий» и «Динамика конструкций», содержит основы и принципы составления уравнений колебаний стволов артиллерийских орудий и дает представление об общем принципе...
Учебное пособие. — Севастополь: Издательство Академии ВМС им. П.С. Нахимова, 2012. — 208 с. Учебное пособие комплексно освещает вопросы живучести нарезных и гладких стволов при использовании боеприпасов послегарантийных сроков хранения. Проблема рассматривается с точки зрения современных представлений технической термодинамики, внутренней баллистики и материаловедения. Особое...
Учебник. — Под редакцией академика генерал-лейтенанта артиллерии А.А. Благонравова. — М.: Народный комиссариат авиационной промышленности СССР (НКАП), Оборонгиз, 1945. — 118 с. В книге описаны все процессы изготовления стволов стрелкового оружия, начиная с выплавки металла и кончая механической обработкой стволов. Металлургические процессы описаны в общих чертах, а механическая...
Под ред. акад. ген.-лейтенанта артиллерии А.А. Благонравова. — М.: НКАП Оборонгиз, Главная редакция вооружения и боеприпасов, 1945. — 226 с. В книге описаны все процессы изготовления стволов стрелкового оружия, начиная с выплавки металла и кончая механической обработкой стволов. Металлургические процессы описаны в общих чертах, а механическая обработка детально; в книге...
Главы из монографии Горохова М.С. Внутренняя баллистика ствольных систем. - М.: Изд-во центрального научно-исследовательского института информации, 1985. - 160 с.
Низкая живучесть артиллерийского ствола становится препятствием на пути совершенствования ствольного комплекса, а вопросы износа и живучести вырастают в проблему, от решения которой зависит прогресс артиллерии....
Учебное пособие. — СПб: Балтийский государственный технический университет (БГТУ) имени Д.Ф. Устинова "Военмех", 2007. — 164 с. — ISBN 978-5-85546-300-2. Учебное пособие охватывает круг вопросов, решаемых на ранних стадиях проектирования стволов артиллерийских орудий среднего и крупного калибров. Описываются рациональные приёмы конструирования стволов, математические модели...
М.: Издание артиллер. управ. УС РККА и НТС треста РУЖ, 1928. — 45 с. Вопрос о правке стволов, имеющий громадное значение в ружейном производстве, до сего времени являлся совершенно не проработанным. Не только теория правки никем не была разработана, но даже и методов практического обучения не существовало. Работа велась опытными мастерами, пополнение которых велось длительным,...
Research paper and PowerPoint presentation. US Army RDECOM-ARDEC-Benet Laboratories. DoD Metal Finishing Workshop, Washington, DC, 2006, - 40 p. State of the Practice. Requirement. Drivers and Barriers. Adoption of Alternatives. Remaining Needs.
Цветной видео-ролик о нарезании артиллерийского ствола. Продолжительность: 2 минуты 24 секунды. Показан принцип, положенный в основу машины по нарезанию нарезов в артиллерийском стволе.
Учебник. — Под ред. Э.А. Горова. — М.: Изд-во арт. инж. академия им. Ф.И.Дзержинского, 1956. — 88 с. Книга предназначается в качестве учебника для слушателей Артиллерийской инженерной академии имени Дзержинского. В ней освещены основные вопросы проектирования стволов стрелкового оружия. Содержание: Устройство стволов. Давление пороховых газов. Прочность моноблоков. Скрепление...
М.; Л.: НКАП, Оборонгиз, 1939. — 165 с. Настоящий труд предназначается в качестве учебного пособия и не претендует на оригинальность. Излагаемый материал мы стремились дать в определённой последовательности и простым языком, чтобы облегчить читателю усвоение рассматриваемых вопросов. При составлении книги мы, безусловно, использовали богатый материал из вышеперечисленных трудов, а...
М., -Л.: НКАП, Оборонгиз, 1939. — 165 с. Настоящий труд предназначается в качестве учебного пособия и не претендует на оригинальность. Излагаемый материал мы стремились дать в определённой последовательности и простым языком, чтобы облегчить читателю усвоение рассматриваемых вопросов. При составлении книги мы, безусловно, использовали богатый материал из вышеперечисленных трудов,...
Учебное пособие. – Л.: Высшее военно-морское орденов Ленина и Ушакова Краснознаменное училище имени М. В. Фрунзе, 1961. — 36 с. В процессе стрельбы ствол артиллерийского орудия изнашивается, то есть внутренняя его поверхность претерпевает такие изменения, которые приводят к нарушению правильности движения снаряда по каналу ствола и в конечном итоге вызывают необходимость замены...
Б.д. — 3 с. Содержание: Данные о характеристиках нарезки для 17 образцов стрелкового оружия. Как определить угол наклона полей нарезов? Как определить шаг нарезов? Чему равна скорость вращения пули при вылете из канала ствола?
Учебное пособие. — М.: ЦНИИ информации, 1974. — 104 с. Данное учебное пособие содержит материалы расчета на прочность всех типов стволов артиллерийских орудий в соответствии с теориями прочности наибольших деформаций и энергии формоизменения, а также расчета живучести стволов, нарезов и системы межслойного охлаждения. Изложенные материалы предназначены для студентов специальных...
Учебник. — М.: Машиностроение, 1976. — 432 с. В книге изложены теоретические основы устройства и проектирования стволов и затворов артиллерийских орудий. Приведены типовые конструктивные схемы современных стволов, казенников, затворов, механизмов полуавтоматики, а также дульных и эжекционных устройств и изложены методы их расчета. Особое внимание уделяется влиянию нагрева и...
Учебник. — М.: Машиностроение, 1976. — 432 с. Изложены теоретические основы устройства и проектирования стволов и затворов артиллерийских орудий. Приведены типовые конструктивные схемы стволов, казенников, механизмов, дульных и эжекционных устройств и изложены методы их расчета. Особое внимание уделено влиянию нагрева и охлаждению стволов. Учебник предназначен для студентов вузов...
Англ. Язык. Transfer of Austrian gun-barrel forging technology to the USSR
An intelligence Memorandum, 1982, -13 p.
The Soviets are using state-of-the-art rotary-forge technology and equipment imported from Austria to produce gun barrels for a wide variety of weapons. The USSR has bought at least 26 automated rotary forges for making gun barrels since the late 1960s from GFM,...
Без входных данных. Документ в PDF-формате. – 2 с. Приведены технические характеристики прибора для лазерного контроля внутренних геометрических размеров труб и измерения отклонения от прямолинейности. Производитель оборудования: ООО "Дизель-тест-Комплект", Россия, г. Екатеринбург. Прибор перемещается по трубе автоматически. Лазерный контроль непрямолинейности от 0,01 мм....
Без входных данных. Документ в PDF-формате. – 2 с. Приведены технические характеристики прибора для лазерного контроля внутренних геометрических размеров труб и лазерного 3D сканирования внутреннего профиля, измерения геометрических размеров труб и видеоконтроля внутренней поверхности. Производитель оборудования: ООО "Дизель-тест-Комплект", Россия, г. Екатеринбург....
Без входных данных. Цветной фильм о системе лазерного 3D сканирования внутреннего профиля. Без текстового сопровождения. Продолжительность: 1 минута 18 секунд. Показано устройство системы лазерного 3D сканирования внутреннего профиля. С использование системы измерения возможно определять дефекты каналов артиллерийских стволов и производить мониторинг живучести артиллерийского...
Без входных данных. Цветной фильм о приборе измерения непрямолинейности трубы (ПИНТ). Без текстового сопровождения. Продолжительность: 2 минуты 23 секунды. С использование прибора измерения непрямолинейности трубы возможно определять дефекты каналов артиллерийских стволов. В фильме показана последовательность проведения измерений.
Автор неизвестен. Электронный документ, - 46 с.
Сборник фотографий иллюстрирует явление разрыва артиллерийского ствола как последствие взрыва боеприпаса в канале ствола.
Автор неизвестен. Электронный документ, - 46 с.
Сборник фотографий иллюстрирует явление разрыва артиллерийского ствола как последствие взрыва боеприпаса в канале ствола.
Одесса: Печатный дом, 2009. — 214 с. — ISBN 978-966-389-245-0. Книга написана исключительно на основании открытых источников и рассчитана на внимание тех читателей, в чьей крови кроме железа гемоглобина, есть немного оружейной стали. Предназначена для полезного и познавательного чтения. Может быть интересна для реставраторов старинного оружия, оружейников, курсантов военных...
Одесса: Печатный дом, 2009. — 214 с. — ISBN 978-966-389-245-0. Книга написана определённо на основании открытых источников и подготовлена на внимание тех читателей, в чьей крови кроме железа гемоглобина, есть чуть-чуть оружейной стали. Предназначена для полезного и познавательного чтения. Может быть достойна внимания для реставраторов многовекового оружия, оружейников, курсантов...
Монография. — М.: Государственное издательство оборонной промышленности, 1939. — 140 с. В книге инженера Сергеева М. М. дано исчерпывающее изложение современных теорий, решающих задачу о дульном тормозе с наибольшим приближением к действительному ходу термодинамических процессов, происходящих в канале ствола после вылета снаряда. Основное назначение книги — дать в руки...
Монография. — М.: Государственное издательство оборонной промышленности, 1939. — 140 с. В книге инженера Сергеева М. М. дано исчерпывающее изложение современных теорий, решающих задачу о дульном тормозе с наибольшим приближением к действительному ходу термодинамических процессов, происходящих в канале ствола после вылета снаряда. Основное назначение книги — дать в руки...
Без входных данных.
Цветной фильм о системе измерения прямолинейности трубы. Без текстового сопровождения.
Продолжительность: 1 минуты 24 секунды.
Показано устройство системы контроля прямолинейности труб. С использование системы измерения возможно определять дефекты каналов артиллерийских стволов.
М.: Оборонгиз, Народный комиссариат авиационной промышленности, 1945. — 181 с. В книге описано устройство каналов стволов орудий, нарезательные станки, инструмент применяемый для нарезания каналов орудий, настройка станка и нарезательной головки, технологический процесс нарезки каналов орудий и дефектов по нарезам. Наряду с описанием приведены конкретные цифровые данные о проверке...
М.: Оборонгиз, 1960. – 337 с.
Книга является учебным пособием для техникумов и содержит описание технологических процессов механической обработки и технического контроля орудийных труб. В книге рассматриваются также общие вопросы проектирования технологического процесса, допуски и возможные точности обработки. Приводимые в книге материалы, учитывающие опыт работы отечественной...
Військово-технічний збірник, 2016. — С. 121-126. (на украинском языке). Оригинальное название: Деградація параметрів стволів артилерійського озброєння в процесі експлуатації. Проведено аналіз процесів i факторіє, що спричиняють деградацію параметрів стволів артилерійського озброєння, запропоновано їхню класифікацію. Розглянуто еєолюцію методів інструментальним контролю стану...
Монография. — Перевод с нем. — Ленинград: Издание Артиллерийской академии РККА им. Дзержинского, 1937. — 204 с. Монография посвящена прочности и живучести стволов огнестрельного оружия. Книга имеет своим назначением заполнить пробелы, образовавшиеся в немецкой артиллерийской литературе вследствие того, что известное капитальное сочинение по проектированию орудийных стволов Г....
Монография. Перевод с нем. -Ленинград: Издание Артиллерийской академии РККА им. Дзержинского, 1937, - 204 с. Монография посвящена прочности и живучести стволов огнестрельного оружия. Книга имеет своим назначением заполнить пробелы, образовавшиеся в немецкой артиллерийской литературе вследствие того, что известное капитальное сочинение по проектированию орудийных стволов Г....
Комментарии